Open the cabin power panel near the driver side dash to locate the correct slot linked to a failed system such as radio, cabin lights, or power outlets. This panel sits behind a removable cover and contains low to mid-range current protection elements.
Each slot is identified by a number and amperage value, typically ranging from 5A to 25A. Lower ratings protect control units and lighting, while higher values handle accessories like power windows and seat adjustments.
Use the printed layout on the cover or service manual chart to match slot numbers with circuit roles. For example, a 10A position may control lighting circuits, while a 20A position may be tied to accessory sockets or electronic modules.
Keep spare inserts and a puller tool available for quick checks during electrical faults. A visual inspection of the internal metal strip often reveals damage without additional tools.
Interior fuse box location in 2010 Dodge Journey and access steps
Remove the panel on the left side of the dashboard to reach the cabin-mounted electrical distribution unit. Open the driver door and locate the removable trim cover at the end of the dash; pull it outward to expose the protected circuits.
This panel contains low and mid-current inserts responsible for lighting, infotainment, and accessory systems. The layout is compact, with numbered positions arranged in rows, making it easier to match each slot with its assigned function using the printed chart.
Access steps
- Open driver door fully for clearance
- Locate side dash cover facing the door frame
- Pull trim panel straight off without tools
- Use built-in puller to remove inserts if needed
Ensure the ignition is off before handling any electrical components and press the cover back firmly after inspection to keep the panel secured and protected from dust.
Full fuse diagram with slot numbers amperage ratings and circuit roles
Match each numbered slot with its listed function before pulling any insert to avoid disabling the wrong system. The layout chart on the cover shows positions in sequence, paired with current values such as 5A, 10A, 15A, and 20A.
Low-current positions, usually 5A and 7.5A, are assigned to memory circuits, control modules, and dashboard electronics. These protect sensitive components that require stable low power.
Mid-range values like 10A and 15A are used for lighting circuits, infotainment, and accessory systems. These slots handle moderate electrical loads and are frequently involved in common faults such as non-working lights or radio issues.
Higher ratings, typically 20A and 25A, support power windows, seat adjustment motors, and auxiliary outlets. These circuits draw more current and are grouped separately within the panel.
Each slot number corresponds directly to a labeled function, allowing quick identification without tracing wires. Numbers are arranged in rows, often starting from the top left and moving across.
Typical assignments include position-based roles such as control unit power, brake light circuits, audio system supply, and accessory sockets. The exact mapping is printed inside the cover for quick reference.
Always verify both the number and amperage marking on the insert before replacement, since identical ratings can serve different systems depending on position.
Using the correct layout chart reduces diagnostic time and prevents unnecessary removal of working components during electrical troubleshooting.
How to check blown fuses and replace them safely in Dodge Journey 2010
Remove the suspected insert and inspect the metal link inside; a break or dark burn mark indicates failure. Use the plastic puller stored in the panel or a small pair of pliers for tight slots.
Turn the ignition off before handling any electrical components to prevent short circuits. Identify the correct slot by matching the system that stopped working with the numbered layout on the cover.
Use a multimeter set to continuity mode for confirmation. A working insert shows a closed circuit, while a damaged one shows no connection.
Compare the amperage value printed on top before installing a replacement. Typical values include 5A, 10A, 15A, and 20A, each designed for specific load ranges.
Insert the new component into the same numbered position and press firmly until fully seated. Loose contact can cause intermittent electrical faults.
After replacement, activate the related system such as lights or power outlets to verify proper operation. Monitor the circuit for a few minutes to ensure stability.
If the new insert fails again, inspect wiring, connectors, or the connected device for faults rather than repeating replacement.
| Step | Action |
|---|---|
| 1 | Locate correct slot using panel layout |
| 2 | Remove insert with puller tool |
| 3 | Inspect metal strip or test with multimeter |
| 4 | Install same amperage replacement |
| 5 | Test system and monitor for repeat failure |